Sandpiper RuppTech Stroke Counter/Batch Control Bedienungsanleitung PDF herunterladen (Seite 5)

Batch Control/Stroke Counter Page 5Batch-sc-rev0611

520-180-000 3/02 Batch Control / Stroke Counter Page 5

Selecting & Storing a Preset Count

ToinitiallystoreorchangeaPresetCountvalue,selectoneofthetenprogram

storagelocations(P0throughP9).PressandholdtheIncreaseDigitbuttonto

displaythecurrentregisterlocation.ThedisplaywillshowP0throughP9forthese

locations.PressandreleasetheIncreaseDigitbuttontosequencethroughto

thelocationwhichwillstorethenewPresetCountvalue,ReleasetheIncrease

Digitbutton.

Afterselectingtheprogramstoragelocation,pressandholdthePresetCount

buttonuntilthefollowingsequenceiscompleted.PresstheResetbuttontoreset

thedisplaytoazerovalue.Thedigitpositionavailableforsettingwillash.Press

andreleasetheIncreaseDigitbuttontochangethedigittotherequiredvalue.

RepeattheprocessusingtheDigitSelectbuttonuntileachdigitlocationisset

asrequired.

Resetting the Total Count

PressandholdintheTotalCountbutton.PressandreleasetheDigitSelect/

Resetbutton.Thedisplaywillresettozero.

Resetting the Preset Count

PressandholdinthePresetCountbutton.PressandreleasetheDigitSelect/

Resetbutton.Thedisplaywillresettozero.Toreprogram,refertotheprocedures

outlinedinSelecting&StoringaPresetCount.

Functions (with the pump running)

START Button - NOTE: Use a momentary contact switch when using a remote

start/stop control.

ThisbuttonisusedonlywhenthecontrolisutilizedasaBatchController.In

thismodeofoperation,thecontrolisusedwithanelectricsolenoidairvalve,which

controlstheairsupplytothepump.Pressingthisbuttonstartsthepump.The

control has an internal connection for utilizing an external or remote

STARTbutton.

STOP Button - NOTE: Use a momentary contact switch when using a remote

start/stop control.

ThisbuttonisonlyusedwhenthecontrolisutilizedasaBatchController.

Pressingthisbuttonstopsthepump.Theunitcanberestartedbypressingthe

STARTbutton.Thecontrolhasaninternalconnectionforutilizinganexternalor

remoteSTOPbutton.WhenaPresetCounthasbeenstoppedbeforecompletion,

thedisplayvalvewillnotash.Thisistoshowthecounthasbeenstopped.When

thepumpstopsaftercompletingaPresetCount,thedisplaypanelwillash.

PROGRAMMING QUICK

REFERENCE

Programming & Storing a Preset

Count

 1.PressandholdPresetCoun

a.PressResettoresetthe 

   displaytozero.

  b.PressandreleaseIncrease

    Digittochangetheashing

   digit.

  c.PressDigitSelectuntileach

    digitisset.

Resetting the Total Count

 1.PressTotalCount.

  a.PressandreleaseReset.

Resetting the Preset Count.

 2.PressandholdPresetCount.

  a.PressandreleaseDigit

   Select/Reset.

Selecting a Program Storage Area

 1.PressandreleaseIncrease 

  Digittosequencethrough

  programstorageareas

  (P0throughP9).

 2.Whenthedesiredstoragearea

  appears,proceedwith

  programingandstorage.

1 2 3 4 5 6 7

Kommentare zu diesen Handbüchern

Keine Kommentare

Sandpiper RuppTech Stroke Counter/Batch Control Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Sandpiper RuppTech Stroke Counter/Batch Control