Sandpiper RuppTech Stroke Counter/Batch Control Bedienungsanleitung PDF herunterladen (Seite 4)

Batch Control/Stroke Counter Page 4Batch-sc-rev0611

520-180-000 3/02 Batch Control / Stroke Counter Page 4

Panel Button Functions

BUTTON ....................................... FUNCTION(S)

Total Count .................................. Display the total or accumulated count.

Digit Select/Reset ....................... Resets the count displayed

(Preset or Total).

Preset Count ............................... Displays the batch size.

Press and hold: Total Count

then press: Increase Digit ........... Moves decimal point.

Press at the same time and hold:

Total Count + Preset Count

then press: Digit Select Selects digit for programming Stroke

Scale Valve. Selected digit will ﬂash.

then press: Increase Digit ........... To program valve to the selected

(ﬂashing) digit.

Increase Digit .............................. Increases value of selected (ﬂashing)

digit. --ALSO-- Selects storage register

for program storage. (P0-P9)

Programming & Set-up Functions (with pump stopped)

Setting the Multiplier or Stroke Scale Value

Eachinputsignal fromthe PulseOutput Interfacemounted onthe pump

registersonecountintothecontrol.Thevalueofthiscountmustbedetermined

at the initial set-up for display purposes. For example, to count only pump

strokes,theStrokeScaleValuewouldbesetat1(one).Onepulsewouldequal

onestroke.

To settheStrokeScaleValue,simultaneously presstheTotal Count and

PresetCountbuttonsinandhold.ThenusetheIncreaseDigitbuttontoenterthe

valueassignedtotheashingdigit.Toprogram,thedigittothefarrightofthe

displayshouldbeashing.Ifitisnotashing,presstheDigitSelectbuttonuntil

thedigittobeprogrammedbeginstoash.Thedecimalpointshouldbetothe

farright.

Moving the Decimal Point for Fractional Volumes

Ifthevalueyouwishtouseisafractionalvolume,suchasdisplacementper

pumpstroke,thedecimalpointmustbemovedintotheproperlocationBEFORE

aStrokeScaleValueisentered.

WhilepressingtheTotalCountbutton,pressandreleasetheIncreaseDigit

buttonuntildecimalpointisinposition.AstheIncreaseDigitbuttonispressed

andreleased,thedecimalpointlocationwill

movefromrighttoleftonthedis-

play.PressandreleaseIncreaseDigit,untilthedecimalpointisinthedesired

position.

Once the decimal point is positioned, set the Stroke ScaleValue.These

instructionsappearintheprevioussection.Also,pleaserefertotheprogramming

andtestingproceduresoutlinedearlierinthismanualfordetailedinstructions.

Thesectionisentitled,ProgrammingforAccuracy.

PROGRAMMING QUICK

REFERENCE

Setting the Decimal Point

1.PressandholdTotalCount.

 a.Repeatedlypressandrelease

  IncreaseDigittomovedecimal

  pointfromrighttoleft.

Setting the Multiplier or Stroke Scale

1. Pressandhold:

 TotalCount+PresetCount.

 a.PressandreleaseDigitSelect

   untildigitashes.

 b.PressIncreaseDigitto 

  programtheashingdigit.

1 2 3 4 5 6 7

Kommentare zu diesen Handbüchern

Keine Kommentare

Sandpiper RuppTech Stroke Counter/Batch Control Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Sandpiper RuppTech Stroke Counter/Batch Control